WELCOME TO Hongkong NKF Machinery Co.,Limited. English | Spanish

bicycle bearings

bicycle bearings
Author :Admin | Publish Date:2013-05-29 17:54:54
Take the wheels off the bicycle beef before greasing the wheel bearings.A mixture of 50 percent white teflon bicycle grease and 50 percent green axle grease works well on bicycle bearings.Don't make the bearing cone too tight when screwing it back into place. Bicycle bearings shouldn't have any play in them and need to roll smoothly.


Bicycle bearings, as most, require a slight preload so that more than one ball under the cone (inner race) will support its load. With proper preload, slight drag should be perceptible. Preload drag is small compared to drag caused by wheel loads, neither of which are significant regardless of adjustment. In contrast bearing life is affected by proper adjustment. Adjusting ball bearings to spin freely unloaded does not reduce operating friction because a bearing with proper preload has lower drag when loaded than one with clearance. For high quality bearings, preload should be just enough to cause light drag when rotating the axle between thumb and forefinger. Low grade ina bearings will feel slightly lumpy with proper preload.


Wheels with quick release (QR) axles present an additional problem in that closing the QR alters bearing clearance. Closing the lever requires increasing manual force with a slight over-center feel near the end of the stroke. This lever force arises from compressing the hollow axle and stretching the skewer. The ratio of elastic length change between axle and skewer is that of their cross sectional area and active lengths.


Although small, axle compression on QR hubs is large enough to alter bearing clearance and should be considered when adjusting bearings. Bearings should be adjusted just loose enough so that closing the QR leaves the fag bearing with a slight preload. Excessive preload from QR closure is the cause of most wheel bearing failures not caused by water intrusion. Clearance, in contrast can be felt as disconcerting rattle when encountering road roughness.


To test for proper adjustment, install the wheel and wiggle the rim side-to-side to determine that there is no clearance (rattle), then let the wheel rotate freely to a stop. If the wheel halts with a short (indexed) oscillation, bearing preload is too high.


Although adjusting QR force is a safety consideration, it is also one of bearing life. It should be kept at a constant level once the desired closure force has been determined. Rear vertical dropouts require a lower and more predictable closure force than was formerly required with axles that could move forward from chain tension. Because vertical dropouts do not rely on friction to resist chain load, many hubs now have smooth faced jam nuts that do not damage dropout faces as older knurl faced ones did.


This is later. [bicycle bearings]  come nicely snug into crowns these days, but sometimes you still find some that are just put loose in the wheel hub. To avoid all of them crashing to the ground with the possibility of vanishing for ever, grab the axle on the side that is still locked in place and point the end that you've just loosened,up. Now it is time to unscrew the locking nut almost completely off the axle. Next, unscrew the bearing cone to expose the wheel bearings to the light of day. Any grease in there? You'd be surprised on how often I open up brand new bikes and find almost nothing.

BRING SKF 6410              ( 50 X 130 X 31) 
BRING SKF 6411              ( 55 X 140 X 33) 
BRING SKF ALS  6            (3/4 X 1 7/8 X 9/16) 

Contact Us

TEL:00852-54978621
FAX:00852-54979628
Email:sales@dbearings.com
Add:UNIT 04,7/F BRIGHT WAY TOWER,NO 33 MONG KOK ROAD,KL
WhatsApp:8618112377009

timken information lists

Copyright © 2014 Hongkong NKF Machinery Co.,Limited. All rights reserved. TEL:00852-54978621 FAX:00852-54979628 Email:sales@dbearings.com